SPB PROTOCOL SERIAL
SPB PROTOCOL CODE
SPB PROTOCOL PC
SPB PROTOCOL PLUS

Now USB is by a wide margin the fastest of the three (by an order of magnitude) but it is also far more complex, with handshaking, device detection, auto speed negotiation etc. between whole systems or devices as opposed to individual chips. UART is more of an external interface, i.e. The only pins of any real interest are just the TX and RX along with a connection to the electrical ground.

SPB PROTOCOL PC

UART is a good quick way to get an embedded micro to talk to a PC as UART to USB adapters are a dollar a dozen (assuming you haven't got any good ol' com ports on your computer). UART requires more work to decode, but as pretty much every processor in existence has a dedicated UART transceiver, this is a non issue. UART reduces the pin count but limits the maximum data rate as the receiver has to try and reverse engineer the data clock from the bitstream.

SPB PROTOCOL SERIAL

UART is the technical name for the kind of serial port you might find on an old 90's PC (serial mouse, keyboard and modem), UART uses half the number of wires as SPI (TX and RX as opposed to data in, data out, clock and chip select). (I2C is another internal serial chip to chip interface that's closer to a low speed UART in terms of complexity and pin count) SPI is an internal interface, pretty much just used between chips on the same PCB. There are 4 pins: MISO (Master-In Slave-Out), MOSI (Master-Out Slave-In), CLK and CS (Chip Select), sometimes its the more ambiguous SDI (serial in), SDO (serial out), SCK (clock) and CE (chip enable) or some variation thereof. At the other end the reverse action is performed. Data gets loaded into a shift register and sent out bit by bit on each clock cycle. SPI is good for embedded stuff as it is just a shift register and not much else, this allows for really fast comms (10Mbps is not uncommon even in tiny 8bit micros with and 50+ in a lot of 32bit chips). I'm sure you already have some experience with USB already, they are all 'serial' as the data is sent one bit at a time down one lane (conga line, one lane highway etc.), as opposed to being split up across several lanes at once (parallel data). There you will find sections that describe in great detail, exactly how each of the MCU's peripherals work. If you haven't already, you should grab the datasheets for your Intel D1000 MCU and start skimming the table of contents. The important thing is that 'serial' by itself is just a word, not a complete standard. You didn't ask about Ethernet, that's yet another serial interface and yet another complicated but well-documented protocol. You can't really bit-bang USB in software, as you could with RS232 or SPI.

SPB PROTOCOL CODE

Typically you use USB by adding handler code to a hardware USB Serial Interface Engine embedded within the microcontroller, or else use a PHY (physical interface) chip. USB uses differential NRZ signalling and is thus much more complicated to describe at the wire level. USB is a more modern interface standard that is described in detail by the USB Implementors Forum documentation I won't rehash the standard here. Transmittting RS232 is straightforward, but receiving RS232 is tricky because of the need to recover the clock signal timing. As such it depends on prearranged agreement between transmitter and receiver, as to the baud rate timing, the number of data bits, whether or not there will be a parity bit, and the minimum number of stop bits. Unlike SPI, RS232 UART uses a single wire to transmit both the clock and data. This is one of the oldest commonly used serial interface protocols, which is why it has so many names. This protocol is often also called 'RS-232(C)' or 'EIA-232' or 'TIA-232' or 'COM port', or several other aliases. UART is the peripheral that sends and received asynchronous serial. SPI is a somewhat loosely defined standard, originally came from the Motorola 68HC11 microcontroller I think. Data can be MSB-first or LSB-first, depending on the connected SPI slave device. Data is transferred simultaneously in and out, typically 8 bits at a time.

SPB PROTOCOL PLUS

SPI has a master clock and synchronous master-in-slave-out and master-out-slave-in data: a total of 3 wires plus ground/power and optional chip-select. Those are three different types of serial interfaces.